Top

No spam, just the best from the world of Flos and design, we promise.

Filter by designers
All,
Filter by families
All,
CASTING_T_100_H700-FOREST-GREEN-1950X1950
Casting-Bollard-Vincent-Van-Duysen-Flos-Outdoor-C-thumb-01.jpg
HyperFocal: 0
HyperFocal: 0
HyperFocal: 0
HyperFocal: 0
Casting-Bollard-Vincent-Van-Duysen-Flos-Outdoor-C-thumb-06
Casting-Bollard-Vincent-Van-Duysen-Flos-Outdoor-C-thumb-07
Casting-Bollard-Vincent-Van-Duysen-Flos-Outdoor-C-thumb-08
Casting-Bollard-Vincent-Van-Duysen-Flos-Outdoor-C-thumb-09
Casting-Bollard-Vincent-Van-Duysen-Flos-Outdoor-C-thumb-10
Casting-Bollard-Vincent-Van-Duysen-Flos-Outdoor-C-thumb-11
Casting-Concrete-Bollard-Vincent-Van-Duysen-Flos-Outdoor-C-12
Casting-Concrete-Bollard-Vincent-Van-Duysen-Flos-Outdoor-C-13
Casting-Concrete-Bollard-Vincent-Van-Duysen-Flos-Outdoor-C-14
Casting-Concrete-Bollard-Vincent-Van-Duysen-Flos-Outdoor-C-15

Colors (6)

Casting T Non Dimmable 100 Forest Green

LED - 3000K - BEAM 50

Item Code: F1257012

The body of the versions T is made of extruded aluminum, base and diffuser in die-cast aluminum EN AB-47100 with a low copper content.
High-resistance coating: after a sandblasting treatment of all components to make the surface porous and ensure a greater adhesion of the paint, the external coating is applied with a double layer with epoxy powders according to the QUALICOAT standard. The first layer of epoxy powder gives chemical and mechanical resistance, the second finishing layer of polyester powder ensures resistance to UV rays and atmospheric agents.
The painted surfaces are treated with alkaline and acidic washes, then rinsed with demineralized water, subjected to a chemical conversion treatment to protect against oxidation. A glass diffuser is glued to the heat sink of the product to ensure a watertight seal, micro-texturized to ensure homogeneous and uniform distribution of the light.
The luminaire is provided with a segment of outgoing cable in neoprene.
We recommend installation on a plinth of cement or on a flat surface.
110/240V power supply integrated.

Also available in: Casting
Technical drawing
Schematic light drawing
Asymmetric
  • Y
  • EXTIP6
  • IK06
  • CM10
  • OTYPE10
  • IC2
Main specifications
  • Lamp category: LED
  • Power (W): 12
  • CCT (K): 3000K
  • CRI: 80
  • Net lumen (lm): 2x256
  • Mountings: Ground
  • Environment: Outdoor wet location
Optical
  • Lighting type: Direct
  • LED type: Power LED
  • Light distribution: Asymmetric
  • Optical type: Asymmetric
  • Beam angle (°): 50
  • Beam angle C90-270 (°): 75
Electrical
  • Frequency (Hz): 50-60
  • Dimmable: No
  • Driver: Integrated
  • Driver type: Non Dimmable
  • Emergency: Without
  • Insulation class: II
Physical
  • Color: Forest Green
  • Orientation: Fixed
  • Weight (kg): 2.30
Notes

We recommend using a connection system with a degree of protection greater than or equal to the degree of protection of the luminaire. During the installation and the maintenance of the fixtures it is important to be careful and avoid damages on the paint coating. Damages on the coating exposed to outdoor conditions or water, could cause corrosion. Chemical substances affect the anticorrosion covering protection. For LED fixtures, there is evidence that most of the damages are connected to electrical effects related to the insulations, which cause destructive electrical discharges These effects are frequently caused by: • over voltage coming from the mains’ network where fixture is connected. • electrostatic discharge (ESD) coming from the environment. The use of a protective device against the overvoltage on the electrical installation is warmly suggest this helps to reduce the intensity of some of these phenomenon and prevent irreversible damages. The selection of the type of device to be used must be adjust on the electrical plant.

Choose the order code

Choose your language

Are you a professional? I'd be happy to help you find a lighting solution!

Book an appointment